Welder (WEL)

2014 Guide - Third Period Package (18 Modules) Comments

Date: 9/18/2026 10:13:13 AM
Module: 120301aA
Version: 1st Edition
Page: 26
Comment: The answer to question 3 should be B, not D.
Status: Approved for Review

Date: 9/18/2026 10:15:29 AM
Module: 120301aA
Version: 1st Edition
Page: 21
Comment: The table on this page does not reflect the recent name change of Canadian Standards Association to CSA Group. It is accurate earlier in the ILM, but it is wrong on this table.
Status: Approved for Review

Date: 9/18/2026 11:22:54 AM
Module: 120302d
Version: 1st Edition
Page: 7
Comment: Question 7 is on a topic and formula not covered in this section or in this ILM at all.
Status: Approved for Review

Date: 9/15/2026 1:14:16 PM
Module: 120303a
Version: 1st Edition
Page: 76
Comment: Question 23 is worded poorly, and the answer in the back does not match the correct answer to the question. So, the question is “what is the outside to outside distance of item #21?” Going off the wording, that could refer to the dimension of the part (item#21 which would be 12”). Understanding the outside to outside portion of the question, to me it would be logical that they are asking for the outside dimension between the parts and where they are placed, as there are two parts. The answer given in the back of the module is as follows 105 1/4” - 32 3/4” - 32 3/4” =39 3/4” This answer would be the outside to outside distance of two of parts 14. My suggestion would be to either change the question to match the answer (what is the outside to outside dimension of the two outside item 14 locations) or to change the wording of the existing question to “what is the dimension of the outside to outside distance between both items 21?” And to also change the answer to match the question (which should be 105.25”-26.75”-26.75”=51.75”)
Status: Approved for Review

Date: 11/5/2026 10:17:01 AM
Module: 120303a
Version: 1st Edition
Page: 67 and 83 to 84
Comment: The answer key lists the answer to question 2 on page 67 as "1." This misalignment seems to apply to the rest of the questions and answers in Section 7: Activity 1.
Status: Approved for Review

Date: 9/18/2026 10:09:50 AM
Module: 120303c
Version: 1st Edition
Page: 65
Comment: The answer to question 3 should be A.
Status: Approved for Review

Date: 11/5/2026 9:59:43 AM
Module: 120303c
Version: 1st Edition
Page: 3
Comment: The second sentence of the last paragraph on page 3 of 120303c reads: "Each spool shows a small enough portion of the job that it can easily be prefabricated, handled, and transported to the job for final assembly." This sentence should read: "Each spool sheet shows a small enough portion of the job...
Status: Approved for Review

Date: 10/13/2026 1:17:54 PM
Module: 120304b
Version: 1st Edition
Page: 39
Comment: #1 - Regarding pg. 39, figure 26, the middle graphic says: Inclination varied to decrease penetration. Electrode pressure may also be decreased, and speed increased. This is wrong! #2 Regarding pg. 39, figure 26 right-hand graphic says: Inclination varied to increase penetration. Electrode pressure may be increased, and speed decreased. This is wrong! Please consult the old 3rd-year module 120302a - version 25, pg. 24 - You will find the correct text in the old module. We have consulted other subject matter experts from other institutions, and they agree.
Status: Approved for Review

Date: 11/12/2026 10:14:47 AM
Module: DP120303c
Version: 1st Edition
Page: Pg. 1 or Drawing No. PCL1-A01-00-AB-XYZ-0001-001
Comment: On drawing number PCL1-A01-00-AB-XYZ-0001-001 the mark numbers associated with Spool 001 and Spool 002 are identical to the mark numbers on control sheets 001 and 002. Whereas, the mark no. for Spool 003 is different than on control sheet 3. The mark number associated with spool 3 on drawing number PCL1-A01-00-AB-XYZ-0001-001 needs to be A00-00-AB-XYZ-00001-001-C.
Status: Approved for Review


Archived Comments

There are no archived comments to view for this package.